Pengaruh Kapasitansi Plasma Kapasitor dan Putaran Mesin Terhadap Konsumsi Bahan Bakar Mesin 125 CC

Akhlis Nur Firman Ardiansyah Santoso; Santoso Santoso

doi:10.61132/venus.v2i4.421

Authors

Akhlis Nur Firman Ardiansyah Santoso Politeknik Negeri Malang
Santoso Santoso Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/venus.v2i4.421

Keywords:

Plasma Capacitor Ignition, capasitor, spesifik fuel consumption

Abstract

The ignition system is an important system in a vehicle. Currently, the level of emissions produced by vehicles continues to increase every year. This can be caused by high fuel consumption values. The solution to this is to improve the quality of the spark plug by adding a capacitor to the ignition/ignition capacitor. The way the Plasma Capacitor Igniton works is by adding a high voltage non-polar capacitor which is connected in parallel to the output coil. The experimental method will be carried out using quantitative methods. By installing ignition plasma capacitors with different capacitor sizes of 1.5 mF (STD), 440 pF, 660 pF installed in parallel with the spark plug wires with variations in engine speed running from 1500 – 5500 rpm to check emissions. To check the fuel consumption value for Rpm 4500 - 9500 which has been adjusted previously. Fuel Consumption Test Results The use of 440 pF capacitors generally provides an increase in SFC efficiency at most engine speeds, with the largest percentage reduction at RPM 5500 (22.64%). The use of 660 pF capacitors shows varying results. At some RPMs, such as 5500, the SFC actually increases (3.77%), while at other RPMs such as 6500, it shows a significant decrease (27.66%).

References

Agus Suprihadi, M. N. (2015). Optimalisasi sistem pengapian CDI (Capasitor Discharge Ignition) pada motor Honda CB 100cc. Nozzle: Journal Mechanical Engineering, 3(1), 1–9. https://doi.org/10.30591/nozzle.v3i1.194

Elfandy, I., Sugiarto, T., Purwanto, W., Setiawan, D., Nasrullah, H., Hamka, J., Tawar, A., Sumatera Barat, P., Otomotif, M., Piksi Ganesha Indonesia Jl Letnan Jenderal Suprapto No, P., & Tengah Indonesia, J. (2023). Analisis variasi hole injector terhadap konsumsi bahan bakar, top speed, dan emisi gas buang sepeda motor matic. MSI Transaction on Education, 4(2), 2721–4893. https://doi.org/10.46574/mted.v4i2.107

Jamaaluddin. (2021). Rancang bangun alat tes busi motor di bengkel motor. J-Eltrik, 1(2), 14. https://doi.org/10.30649/j-eltrik.v1i2.14

Munthe, I. (2019). Pengaruh sistem pengapian CDI AC dan DC terhadap kadar gas buang CO, HC dan konsumsi bahan bakar pada mesin 110cc. JTIK (Jurnal Teknik Informatika Kaputama), 3(2), 69–80. https://doi.org/10.59697/jtik.v3i2.645

Sugeng, M., & Mukti, Y. (2020). Analisis perbandingan koil pengapian standard dan koil pengapian aftermarket terhadap kinerja sepeda motor 4 langkah. Bina Teknika, 15(2), 147. https://doi.org/10.54378/bt.v15i2.1279

Suriaman, I., Nurikhsan, R. A., Yusuf, N., Subekhi, T. B. U. A., & Anwar, C. (2023). Analisis pengaruh sistem pengapian CDI standar dan modifikasi pada motor Vario 110cc. Jurnal Mekanik Terapan, 4(1), 1–8. https://doi.org/10.32722/jmt.v4i1.5606

Ubaidillah, A., Prasetyo, I., & Setiawan, S. (2022). Pengaruh jumlah lilitan groundstrap pada kabel busi terhadap daya dan torsi pada sepeda motor Supra 125. Surya Teknika, 6, 13–18. https://doi.org/10.48144/suryateknika.v6i2.1355

Wulansari, A., Sakti, G., & Alqadri, M. I. (2020). Pengaruh kapasitor pararel dengan spark plug terhadap daya dan torsi piston engine compression ratio 9:1. Jurnal Penelitian Politeknik Penerbangan Surabaya, 5(4), 306–315.