Fabrikasi Profil Siku Baja Penyangga Rak Dinding Ukuran 150x150x0,5mm,  Kapasitas 40 Biji/Jam

Farhan Alif Hidayatulloh; Syamsul Hadi; Diandra Satria Pangestu; Ahmad Faisal; Tabing Kautsar Alhidayat; Viqo Andrean Maulana

doi:10.61132/jupiter.v4i3.1400

Fabrikasi Profil Siku Baja Penyangga Rak Dinding Ukuran 150x150x0,5mm, Kapasitas 40 Biji/Jam

Authors

Farhan Alif Hidayatulloh Politeknik Negeri Malang
Syamsul Hadi Politeknik Negeri Malang
Diandra Satria Pangestu Politeknik Negeri Malang
Ahmad Faisal Politeknik Negeri Malang
Tabing Kautsar Alhidayat Politeknik Negeri Malang
Viqo Andrean Maulana Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/jupiter.v4i3.1400

Keywords:

6 Hole Drilling, Low Carbon Steel, Shelf Support Angle Profile, Support Wall, V-Die Press Brake

Abstract

The weak and less rigid profile of the shelf support elbow on the supporting wall with dimensions of the two elbows 15 cm long, 3.5 cm wide, 0.5 mm thick from low carbon steel is the problem faced. The purpose of fabrication is to obtain a shelf support elbow profile with dimensions of the two elbows 15 cm long, 3.5 cm wide, 0.5 mm thick from low carbon steel that is strong and stiff enough. The manufacturing method includes: design of the shelf support elbow profile, selection of 0.5 mm thick plate from low carbon steel, precision cutting (shearing) measuring 30 cm long, 3.5 cm wide, bending at a 90o angle with a V-die press brake machine, forming a 3 mm radius reinforcing groove for the 90o angle, drilling 6 holes with a diameter of 3.5 mm, finishing and painting, and quality and dimension inspection. The fabrication results are in the form of a shelf support angle profile on a supporting wall with dimensions of 15 cm in length for both angles, 3.5 cm in width, 0.5 mm in thickness from low carbon steel that can withstand a load of 2 kg, a total production cost of IDR 14,000/unit, a production process duration of 1.5 minutes/unit which implies that the shelf support angle profile is able to withstand vertical loads with 3 steel screws with a diameter of 3 mm x 35 mm.

References

Anwar, C., Rahdiana, N., & Ramadhan, A. I. (2020). Analisis pengaruh radius dies terhadap springback logam lembaran stainless-steel pada proses bending hidrolik V-die. Jurnal Teknologi, 12(2), 124–132. https://doi.org/10.24853/jurtek.12.2.123-132

Arendi, Y. A., & Akhmad, H. A. R. (2025). Pengaruh metode pemotongan plat baja ST37 terhadap kekuatan. Jurnal Teknik Mesin, 14(2), 85–92.

Aryoseno, M. A., Rahmiati, T., & Rosidi. (2023). Analisis pengaruh gaya tekan terhadap fenomena springback pada alat V-bending plat manual. Prosiding Seminar Nasional Teknik Mesin, 13(2), 1563–1570.

ASM International. (2006). ASM handbook, volume 14A: Metalworking—Sheet forming. ASM International.

Bonardo, M. (2023). Pembuatan alat pemotong plat manual. Jurnal Teknik, Komputer, Agroteknologi dan Sains, 2(1), 79–91. https://doi.org/10.56248/marostek.v2i1.97

Carli. (2017). Hasil pemotongan press tool pemotong strip plat pada mesin tekuk hidrolik Promecam di laboratorium pemesinan. Jurnal Rekayasa Mesin, 10(3), 86–90. https://doi.org/10.32497/rm.v10i3.149

Dahlan, R. (2025). Pengaruh penyesuaian sudut terhadap desain permukaan die pada simulasi pembentukan logam pelat. Jurnal Ismetek, 19(2), 126–132.

Dini, O., Saepudin, A., & Maulana, M. R. (2025). Rancang bangun alat uji bending pada plat besi menggunakan hydraulic jack kapasitas 6 ton. Journal of Science & Engineering, 5(1), 151–154. https://doi.org/10.54199/pjse.v5i1.492

Farhan, M., Pradana, R. A., & Widodo, M. A. (2025). Pengaruh jumlah partikel SiC terhadap karakteristik material faktual dibuat melalui teknik metalurgi serbuk. Jurnal Rekayasa Mesin, 20(1), 147–154. https://doi.org/10.32497/jrm.v20i1.6205

Groover, M. P. (2020). Fundamentals of modern manufacturing: Materials, processes, and systems (7th ed.). John Wiley & Sons.

Hadi, S., Hardjito, A., Wicaksono, H., Firmansyah, H. I., Amrullah, R. N., Permana, R. W., & Takwim, R. N. A. (2025). Minimalizing spring back of metal plates bending effect by squishing with press tool. Engineering Science and Management, 13(4), 373–380. https://doi.org/10.5267/j.esm.2025.8.001

Hermani, B., & Muhtar, D. O. (2022). Design of roll sheet metal forming machine. MEstro Jurnal Ilmiah, 4(2), 32–37.

Hosford, W. F., & Caddell, R. M. (2011). Metal forming: Mechanics and metallurgy (4th ed.). Cambridge University Press.

Janatama, R., & Rizkia, V. (2023). Pengaruh jenis material logam lembaran dan radius lengkungan dies set pad dan punch terhadap hasil sudut tekuk proses U-die bending. Prosiding Seminar Nasional Teknik Mesin Politeknik Negeri Jakarta, 406–415.

Kalpakjian, S., & Schmid, S. R. (2014). Manufacturing engineering and technology (7th ed.). Pearson Education.

Khoryanton, A., Purnomo, A., Putri, F. T., & Nashrullah, M. (2021). Penerapan teknologi mesin bending guna mempercepat proses bending pada produk gantungan ayam di PT Todda Perkasa Semarang Ampala. Jurnal Rekayasa Mesin, 16(3), 417–424. https://doi.org/10.32497/jrm.v16i3.3059

Marjuki, I., Ses, B., Polonia, E., & Rahmadi, H. (2024). Alat pemotong plat sistem geser. Indonesian Journal of Mechanical Engineering Vocational, 4(1), 8–12.

Putra, M. A., & Rochyat, I. G. (2017). Rancang bangun rak multiguna ergonomis untuk menggantung jaket dan helm. Jurnal Inosains, 12(2), 42–47.

Saktisahdan, T. J. S. (2019). Pengaruh proses heat treatment terhadap perubahan. Jurnal Laminar, 1(1), 28–33.

Suryadi, R., Nugroho, S. A., & Muhardi. (2016). Pengaruh beban vertikal terhadap daya dukung lateral pondasi tiang. JOM FTEKNIK, 3(1), 1–9.

Suyuti, M. A., Nur, R., & Iswar, M. (2020). Rancang bangun press tool untuk alat bending pelat tipe die-V air bending. Jurnal Teknik Mesin, 6(1), 39–45. https://doi.org/10.33019/jm.v6i1.1396

Syamsuir, Lubi, A., & Susetyo, F. B. (2020). Karakteristik sifat mekanik dan struktur mikro baja karbon sedang paska perlakuan panas tempering. Jurnal Kajian Teknik Mesin, 7(1), 1–7.

Tuwanakotta, E., & Paa, A. R. (2022). Pengaruh bentuk profil tersusun terhadap perilaku elemen kolom baja. Jurnal Karkasa, 8(2), 50–56.

Widjaja, H., & Khairuman, R. R. (2025). Analisis springback pelat ST37 dengan tegangan tarik 343 N/mm² tebal 1,98 mm pada proses V-bending dengan sudut 120°, 135°, dan 150° serta arah tekukan berlawanan grain direction pelat. Jurnal Teknologi dan Rekayasa Manufaktur, 7(1), 11–22. https://doi.org/10.48182/jtrm.v7i1.176

Wijaya, D. R., & Willis, G. R. (2025). Analisa efisiensi rasio sisa potong dalam proses. Jurnal Teknik, 2(6), 781–785.

Downloads

Published

2026-05-31

How to Cite

Farhan Alif Hidayatulloh, Syamsul Hadi, Diandra Satria Pangestu, Ahmad Faisal, Tabing Kautsar Alhidayat, & Viqo Andrean Maulana. (2026). Fabrikasi Profil Siku Baja Penyangga Rak Dinding Ukuran 150x150x0,5mm, Kapasitas 40 Biji/Jam. Jupiter: Publikasi Ilmu Keteknikan Industri, Teknik Elektro Dan Informatika, 4(3), 122–132. https://doi.org/10.61132/jupiter.v4i3.1400