Manufaktur Klem U Batang Baja, Panjang 15 cm, M10 untuk Pipa 1,5”, Kapasitas 5 Unit/Jam

Abdillah Yusuf Kafabihi; Syamsul Hadi; Mohammad Rizal Abimanyu; Muhammad Yusuf Alfarizi; Revi Igo Agustian

doi:10.61132/jupiter.v4i3.1404

Manufaktur Klem U Batang Baja, Panjang 15 cm, M10 untuk Pipa 1,5”, Kapasitas 5 Unit/Jam

Authors

Abdillah Yusuf Kafabihi Politeknik Negeri Malang
Syamsul Hadi Politeknik Negeri Malang
Mohammad Rizal Abimanyu Politeknik Negeri Malang
Muhammad Yusuf Alfarizi Politeknik Negeri Malang
Revi Igo Agustian Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/jupiter.v4i3.1404

Keywords:

ASTM A36 steel, M10 bolt thread, piping system, steel bar bending, U-bar clamp

Abstract

The weak strength of the U-bar clamp material for the piping system grip is a problem faced. The manufacturing objective is to obtain a U-bar clamp from ASTM A36 steel, 15 cm long for a 1.5” pipe support with M10 bolt threads. The manufacturing method includes: design of a 15 cm long U-bar clamp for a 1.5” pipe with M10 bolt threads, selection of ASTM A36 steel material, cutting 10 mm diameter steel steel to 15 cm long, making M10 bolt threads at both ends for 20 mm, bending the steel U-bar clamp with a distance between the axes of 48 mm, making a clamp plate measuring 75x24x2 mm in length with 2 holes of 11 mm in diameter, coating the U-clamp and clamp plate by immersing it in molten Zinc at 500oC for 1 minute, installing 2 M10 nuts, and checking the quality and dimensions. The manufacturing results are in the form of ASTM A36 steel bar U-clamps, 15 cm long for 1.5” pipes with M10 bolt threads 20 mm long, total production costs of IDR 11,000/unit, and a process duration of 12 minutes/unit which implies that the steel bar U-clamps are strong enough to support water-filled pipes with an installation distance of every 1 m and are rust-resistant with galvanizing.

References

Achmaddillah, D. A. P., Hadi, S., Nursyifa, K. A., Nugroho, A. S., Fahrezi, M. H. R., & Maulana, G. A. F. (2026). Analisis hasil uji tarik baja karbon penampang silindris dan segiempat. Konstruksi: Publikasi Ilmu Teknik, Perencanaan Tata Ruang dan Teknik Sipil, 4(1), 11–19. https://doi.org/10.61132/konstruksi.v4i1.1285

Arjunan, R., & Murugan, G. (2025). Analysis of failure of bolt loosening and fatigue. International Journal for Research in Applied Science & Engineering Technology (IJRASET), 13(2), 779–783. https://doi.org/10.22214/ijraset.2025.66977

Chun, M., Kim, J., Kim, K., Jeong, D., Lee, D., Wi, S., Kim, B., Kim, C., & Shim, C. (2024). A fundamental study on structural strength assessment of U-bolts for expanded application to shipbuilding and offshore piping systems. International Journal of Naval Architecture and Ocean Engineering, 16, 100561. https://doi.org/10.1016/j.ijnaoe.2023.100561

Faza, A., & Faridzi, A. (2024). Ketahanan baja ASTM A36 terhadap pengujian SMAW dan metalografi. Jurnal Rekayasa Sistem Engineering dan Manufaktur, 2(2), 109–118. https://doi.org/10.30651/resem.v2i2.21911

Gideon, S., & Betesda, Y. C. (2025). Evaluasi kuantitatif serta analisis kerugian mayor dan minor pada sistem perpipaan NaOH 29–31% di Chlor Alkali Plant PT X, Porsea. Jupiter: Publikasi Ilmu Keteknikan Industri, Teknik Elektro dan Informatika, 3(4), 110–120. https://doi.org/10.61132/jupiter.v3i4.952

Grzejda, R. (2021). Finite element modeling of the contact of elements preloaded with a bolt and externally loaded with any force. Journal of Computational and Applied Mathematics, 393, 113534. https://doi.org/10.1016/j.cam.2021.113534

Hadi, S. (2016). Teknologi bahan. Andi Publisher.

Hadi, S., Irawan, B., Purwoko, P., Buwono, H. P., Murdani, A., & Zainuri, A. M. (2023). Desain pagar berduri fleksibel pembatas area berpondasi beton, pipa galvanis dan klem-U. Jurnal Pengabdian kepada Masyarakat, 13(1), 60–69. https://doi.org/10.30999/jpkm.v13i1.2458

Hadi, S., Muzaki, M., Murdani, A., & Aida, F. (2025). Desain dan pembuatan perangkat pembentuk penggantung pakaian bentuk S bersudut 90°. Jurnal Pengabdian kepada Masyarakat, 12(2), 214–220. https://doi.org/10.33795/abdimas.v12i2.9112

Hamdani, Y., & Marthiana, W. (2024). Analisis laju korosi pada baja ASTM A36 dengan variasi temperatur dan waktu perendaman dalam aliran air laut. Teknosia, 18(2), 72–78. https://doi.org/10.33369/teknosia.v18i2.33425

Hendri, D., Irwansyah, I., Susanto, H., & Ali, S. (2024). Analisa kegagalan baut pengikat pelat trunnion linner pada unit cement mill 1 di PT. X. Jurnal Mekanova, 10(1), 253–261.

Herawati, E., Sadiyo, S., Nugroho, N., Karlinasari, L., & Yoresta, F. S. (2017). Karakteristik kekuatan leleh lentur baut besi dengan beberapa variasi baut. Jurnal Teoritis dan Terapan Bidang Rekayasa Sipil, 24(3), 217–222. https://doi.org/10.5614/jts.2017.24.3.4

Hikari, A. F. S., Faraby, A. W. A., Mauldani, R., Zulfikar, M., Permata, E., & Hastuti, S. (2026). Kajian literatur: Springback pada proses bending logam tipis. Global Research and Innovation Journal (GREAT), 2(1), 58–63.

Kayadoe, V., & Filindity, Y. T. (2020). Kondisi optimum elektroplating baja karbon rendah menggunakan logam seng (Zn). Jurnal Manumata dan Sains, 2(1), 44–54. https://doi.org/10.30598/jmsvol2issue1pp44-54

Kurniawan, M. D., Hadi, S., Rangga, M., Firmansyah, F. Y., & Yoga, M. (2025). Perencanaan penggantian komponen mobil penumpang muatan 15 orang periode 2026. Venus: Jurnal Publikasi Rumpun Ilmu Teknik, 3(6), 293–302. https://doi.org/10.61132/venus.v3i6.1268

Liu, Z., & Phares, B. M. (2020). Determination of U-bolt connection load capacities in overhead sign support structures. Journal of Constructional Steel Research, 170, 106096. https://doi.org/10.1016/j.jcsr.2020.106096

Nugroho, C. B., & Hidayat, R. (2016). Studi cacat permukaan plat aluminium pada proses pembengkokkan sudut mesin bending. Jurnal Integrasi, 8(2), 88–92.

Nur, R., Suyuti, M. A., Reza, M., & Misbahuddin, B. (2019). Pengaruh sudut punch dan ketebalan pelat terhadap springback pada bending V. Sinergi, 17(1), 57–64. https://doi.org/10.31963/sinergi.v17i1.1593

Patil, H., Kolhe, S. I., & Student, T. (2019). Experimental investigation of U bolt used in leaf spring of fan automobile for various loads. International Journal of Trend in Scientific Research and Development, 3(6), 465–469. https://doi.org/10.5281/zenodo.3588068

Rachman, R., Almahdi, A., & Yuhas, D. (2022). Kajian pengaruh jenis material terhadap kualitas ukuran pada proses penekukan pelat dengan metoda ANOVA. Poli-Teknologi, 20(3). https://doi.org/10.32722/pt.v20i3.3826

Saber, M., & Chouikhi, H. (2023). Finite element analyses of bolted joints using different thread modelling techniques. Tehnički Vjesnik, 30(1), 178–184. https://doi.org/10.17559/TV-20220504091929

Vahedi, M., Ebrahimian, H., & Itani, A. M. (2023). Full-scale testing and analytical modeling of rebar cages reinforced with mechanical U-bolt connectors. Applied Sciences, 13(14), Article 8113. https://doi.org/10.3390/app13148113

Yang, G., Yang, L., Chen, J., Xiao, S., & Jiang, S. (2021). Competitive failure of bolt loosening and fatigue under different preloads. Chinese Journal of Mechanical Engineering, 34, 1–11. https://doi.org/10.1186/s10033-021-00663-3

Zhao, P., Liu, J., Gao, H., & Xue, F. (2023). Study on tightening, anti-loosening, and fatigue resistance performances of bolted joints with different anti-loosening washers and nuts. Applied Sciences, 13(24), Article 13253. https://doi.org/10.3390/app132413253

Zulfikar, M., Maryadi, M., Arifiansah, A., & Fahrudin, T. (2025). Analisa perbandingan hasil pengelasan GTAW dan SMAW pada pipa A36 dengan metode uji radiografi. Venus: Jurnal Publikasi Rumpun Ilmu Teknik, 3(4), 208–218. https://doi.org/10.61132/venus.v3i4.1062

Downloads

Published

2026-05-31

How to Cite

Abdillah Yusuf Kafabihi, Syamsul Hadi, Mohammad Rizal Abimanyu, Muhammad Yusuf Alfarizi, & Revi Igo Agustian. (2026). Manufaktur Klem U Batang Baja, Panjang 15 cm, M10 untuk Pipa 1,5”, Kapasitas 5 Unit/Jam. Jupiter: Publikasi Ilmu Keteknikan Industri, Teknik Elektro Dan Informatika, 4(3), 166–181. https://doi.org/10.61132/jupiter.v4i3.1404