Analisa Desain Rangka Mesin Rotary Dryer untuk Pengeringan Maggot Menggunakan Metode Finite Element Analysis

Ahmad Rifqi Shulkhan; Ikhwan Taufik; Sigit Mujiarto; Tri Retno Setiyawati; Arif Rahman Saleh

doi:10.61132/venus.v3i3.890

Authors

Ahmad Rifqi Shulkhan Universitas Tidar
Ikhwan Taufik Universitas Tidar
Sigit Mujiarto Universitas Tidar
Tri Retno Setiyawati Universitas Tidar
Arif Rahman Saleh Universitas Tidar

DOI:

https://doi.org/10.61132/venus.v3i3.890

Keywords:

Rotary Dryer Machine, Maggot & Finite Element

Abstract

Organic waste management is an important issue in addressing environmental problems. One potential solution is bioconversion technology using Black Soldier Fly (BSF) maggots that can break down organic waste and produce larvae with economic value as animal feed. To increase the selling value and extend the shelf life, BSF larvae need to be dried using tools such as rotary dryers. This study aims to design and analyse the strength of a rotary dryer machine frame for maggot drying with a Finite Element Analysis (FEA) approach based on SolidWorks software. Simulations were carried out on several materials: ASTM A36, AISI 1020 Steel, and AISI 1045 Steel. The analysis results show that all materials are within safe limits based on Von Mises stress, deformation, and safety factor. AISI 1045 steel material gives the best performance with Von Mises stress of 14.238 MPa, deformation of 0.59 mm, and safety factor of 7.2. These results show that AISI 1045 steel is the most recommended material for the rotary dryer frame.

References

Dortmans, B., Diener, S., Verstappen, B., & Zurbrügg, C. (2017). Proses Pengolahan Sampah Organik dengan Black Soldier Fly (BSF). Leanza Mediaproduktion GmbH.

Effendy, S., Syarif, A., Rendi Setiady, R., & Anjas Abdul Kholik, M. (2018). Kajian Prototipe Rotary Dryer Berdasarkan Kecepatan Putaran Silender Pengering dan Laju Alir Udara Terhadap Efisiensi Thermal Pengering Biji Jagung Study Of Rotary Dryer Prototype Based On The Revolutions Of the Dryer and Air Flow Rate Towards the Thermal Efficiency of Drying Corn Seeds. Jurnal Kinetika, 9(02), 43–49.

Hidayat, D. P., & Tamjidillah, M. (2022). Perancangan Dan Pembuatan Alat Pemotong Kerupuk Otomatis Dengan Kapasitas 60 Kg Per Jam. Jtam Rotary, 4(2), 151. https://doi.org/10.20527/jtam_rotary.v4i2.6666

Moretta, A., Salvia, R., Scieuzo, C., Di Somma, A., Vogel, H., Pucci, P., Sgambato, A., Wolff, M., & Falabella, P. (2020). A bioinformatic study of antimicrobial peptides identified in the Black Soldier Fly (BSF) Hermetia illucens (Diptera: Stratiomyidae). Scientific Reports, 10(1).

Nurdin, H., Waskito, & Ambiyar. (2020). Perencanaan Elemen Mesin.

Rahmi, M., & Canra, D. (2018). Analisis Kekuatan Ball Valve Akibat Tekanan Fluida Menggunakan Finite Element Analysis. Jurnal Teknologi Terapan |, 4(2).

Rukmini, P., Luthfiana Rozak, D., Winarso, S., & Pendidikan Guru Sekolah Dasar STKIP, P. N. (2020). Pengolahan Sampah Organik Untuk Budidaya Maggot Black Soldier Fly (BSF).

Sholahuddin, S., Wijayanti, R., Supriyadi, S., & Subagiya, S. (2021). Potensi Maggot (Black Soldier Fly) sebagai Pakan Ternak di Desa Miri Kecamatan Kismantoro Wonogiri. PRIMA: Journal of Community Empowering and Services, 5(2), 161.

Sultan, U., & Tirtayasa, A. (2022). Strategi Pengolahan Limbah Organik Melalui Budidaya Maggot Untuk Menghasilkan Nilai Tambah Ekonomi Warga Desa Domas Usman 1.