Analisis Pemeliharaan Mesin Bubut Tipe C6240A di CV Karya Polyurethane
DOI:
https://doi.org/10.61132/venus.v3i3.953Keywords:
Machine Maintenance, Lathe Machine C6240A, Industrial Equipment ManagementAbstract
This The maintenance objectives of a C6240A-type lathe involve a number of crucial aspects, including gears, tool bits, toolposts, lower sled and upper sled. This study was to investigate effective maintenance strategies for each of these components, focusing on preventive and predictive maintenance. Gears: Regular lubrication is also necessary to ensure smooth gear movement and prevent excessive friction that could lead to failure. Chisel Bits: Monitoring the condition of the tool blade needs to be done regularly. Toolpost: The toolpost needs to be checked periodically to ensure availability and safety of the cutting tool. Bottom and Top Slings: Maintenance of the lower and upper slings involves checking for tension and wear. C6240A type lathe users can minimize the risk of failure, improve operational efficiency, and extend the life of the machine. The method used in this research is a qualitative method, by means of observation and interviews. The results of this study are that the gears can be more durable because lubrication is always given and not easily thirsty, the tool blade is not easily blunted because the workpiece is fed little by little, and frequent honing is done to keep it sharp. The locking toolpost is not easily damaged if you use a rubber hammer when locking, the bottom row makes a change of ashock so that it can do automatic turning. This maintenance can increase the life of the lathe for longer operation.
References
Abdillah, H., & Sidik, M. (2023). Analisa pemeliharaan mesin bubut dengan Fault Tree Analysis (FTA) dan Failure Mode and Effect Analysis (FMEA) di CV. Maja Teknik Pandeglang.
Akbar, M. R., & Widiasih, W. (2022). Analisis perawatan mesin bubut dengan metode preventive maintenance guna menghindari kerusakan secara mendadak dan untuk menghitung biaya perawatan. Jurnal SENOPATI.
Ardiansyah, A., & Faisal, M. (n.d.). Rancang bangun mesin pengupas jagung menggunakan dinamo elektrik.
Ben-Daya, M., & Rahim, M. A. (2000). Effect of maintenance on the economic design of x̄-control chart. European Journal of Operational Research, 120(1), 131–143. https://doi.org/10.1016/S0377-2217(98)00379-8
Harsanta, H., & Suhadi, A. (n.d.). Program Studi Magister Teknik Mesin.
Haruyama, S., Nurhadiyanto, D., Choiron, M. A., & Kaminishi, K. (2013). Influence of surface roughness on leakage of new metal gasket. International Journal of Pressure Vessels and Piping, 111–112, 146–154. https://doi.org/10.1016/j.ijpvp.2013.06.004
Hidayat, T., Abizar, H., & Rokhadhitomo, O. (n.d.). Analisis pemeliharaan preventif pada mesin horizontal sand mill tipe ROOT RTSM-50ADL E. Jurnal Pendidikan Teknik Mesin Undiksha, 11(1). https://doi.org/10.23887/jptm.v11i1.54362
Irdianto, I. (2019). Penggunaan metode Markov Chain dalam penjadwalan pemeliharaan mesin untuk meminimalkan biaya kerusakan mesin dan pemeliharaan mesin mill 303 di PT. Steel Pipe Industry of Indonesia Unit 3. Jurnal Teknik Mesin, 2(1), 11–17.
Khazanah, N., Mesin, T., Bengkalis, P. N., & Alam, B. S. (2019). Seminar Nasional Industri dan Teknologi, Politeknik Negeri Bengkalis Oktober 2019.
Kurniawan, R. A., & Mujayin, H. (2015). Usulan pemeliharaan mesin stitching dengan metode Reliability Centered Maintenance. Jurnal Teknik Industri, 16(2), 83–91.
Lestari, L., & Rafi, M. (n.d.). Rekondisi mesin bubut AJAX BU-14 di Laboratorium Mekanik Politeknik Manufaktur Negeri Bangka Belitung: Proyek akhir.
Liu, H., & Singh, P. (2002). MAKEBELIEVE: Using commonsense knowledge to generate stories. Retrieved from http://www.aaai.org
Moubray, J., & Pérez, C. M. (n.d.). El camino hacia el RCM – Mantenimiento centrado en confiabilidad. http://www.soporteycia.com.co
Mulyaningsih, S., Mindhayani, I., & Sain, F. (2022). Perencanaan pemeliharaan mesin bubut di lingkungan Laboratorium Geologi Teknik Institut Sains & Teknologi AKPRIND Yogyakarta. Jurnal Rekayasa Industri (JRI), 4(1).
Ralph, A. P., et al. (2010). A simple, valid, numerical score for grading chest x-ray severity in adult smear-positive pulmonary tuberculosis. Thorax, 65(10), 863–869. https://doi.org/10.1136/thx.2010.136242
Sukopriyanto, A., Rahayuningsih, S., & Komari, A. (2019). Perancangan penjadwalan pemeliharaan mesin bubut dengan metode Reliability Centered Maintenance (RCM) di bengkel pemesinan SMK Negeri 1 Kediri. Jurnal Ilmiah Mahasiswa Teknik Industri Universitas Kadiri, 1(Januari), 13–23. http://ojs.unik-kediri.ac.id/index.php/jurmatis/index
Syahabuddin, A. (2019). Analisis pemeliharaan mesin bubut CY-L1640G dengan metode Reliability Centered Maintenance (RCM) di PT. Polymindo Permata.
Umar Syah, I., & Sumirat, U. (2017). Pencapaian kompetensi siswa SMK dalam praktik bekerja dengan mesin bubut.
Utomo, A. I., & Santoso, D. T. (2022). Implementasi FMEA (Failure Mode and Effect Analysis) pada mesin bubut konvensional di PT. Raja Ampat Indotim. Jurnal Teknik Mesin dan Pembelajaran, 5(1), 17–24. https://doi.org/10.17977/um054v5i1p17-24
Wahyudi, F. D., Remawati, D., & Harsadi, P. (2019). Sistem pakar deteksi kerusakan mesin bubut dengan metode KNN. Jurnal Teknologi Informasi dan Komunikasi (TikomSin), 6(2), 7–13. https://doi.org/10.30646/tikomsin.v6i2.370
Wardani, A. D., Riyadi, S., Pratomo, L. H., & Setiawan, F. B. (2021). Peningkatan efisiensi kinerja Switched Reluctance Motor dengan metode pergeseran sudut fasa. TEKNIK, 42(1), 253–259. https://doi.org/10.14710/teknik.v42i3.33970
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Venus: Jurnal Publikasi Rumpun Ilmu Teknik
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
