Umur Lelah Hasil Cetak Injeksi Bahan Campuran Daur Ulang dari Polipropilin dan High Impact Polystyrene

Syamsul Hadi; Daffa Aureza Andhika; Ivan Rosdinata; Dhea Septa Ristiana; Khoirul Anam; Zakijah Irfin

doi:10.61132/venus.v3i6.1238

Authors

Syamsul Hadi Politeknik Negeri Malang
Daffa Aureza Andhika Politeknik Negeri Malang
Ivan Rosdinata Politeknik Negeri Malang
Dhea Septa Ristiana Politeknik Negeri Malang
Khoirul Anam Politeknik Negeri Malang
Zakijah Irfin Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/venus.v3i6.1238

Keywords:

Fatigue Life, Injection Molding, S-N Curve, Used HIPS, Used PP

Abstract

Waste from used Polypropylene (PP) and High Impact Polystyrene (HIPS) plastic is problematic in its management. The purpose of this research is to obtain the fatigue life of a mixture of used PP and HIPS plastics in its pure plastic. The research method is through the stages of mixing pure PP and 50% volume of used PP, pure HIPS and 50% volume of used HIPS, injection molding of R.R. Moore standard fatigue test specimens for pure PP, pure HIPS, pure PP + used PP, and pure HIPS + used HIPS, checking the straightness and smoothness of the molded specimen surface, fatigue testing with increasing serial loads, analysis of the bending stress curve (S) against fatigue life (N). The results showed that mixing used PP and used HIPS in pure plastic affected the fatigue life at the test speed (n)=2100 rpm for recycled PP was 9.84% shorter than pure PP, and at n=1600 rpm for recycled PP it was 9.32% shorter than pure PP, while at n=2100 rpm for recycled HIPS it was 4.45% shorter than pure HIPS, and at n=1600 rpm for recycled HIPS is 4.77% shorter than pure HIPS, while the fatigue life of pure PP is 1627704 cycles and the fatigue life of pure HIPS is 1291636 cycles or the fatigue life of pure HIPS is 20.65% shorter than pure PP, the implication of which is that the addition of used PP and used HIPS reduces the fatigue life to 9.84% for PP and 4.45% for HIPS.

References

Adhiharto, R. Krismawanto, Hakim, T. A.R.& Komara, A.I. (2018). Studi Rancang Bangun Mesin Benchtop Injection Molding sebagai Aletrnatif Pengolahan Limbah Botol Plastik. Conference Paper, 1-9. https://www.researchgate.net/publication/324314932

Andriansyah, S., Asyari, T.A., Wiradinata, Susanto, H. & Sugiyanto, D. (2024). Pengaruh Temperatur terhadap Shrinkage Hasil Cetakan Model Cup pada Proses Injection Molding. Metalik: Jurnal Manufaktur, Energi, Material Teknik, 3(2), 38-44. DOI:10.22236/metalik.v3i2.16574

Anonim, (2025a). https://laminatedplastics.com/polypropylene.pdf, diakses 25 November 2025.

Anonim, (2025b). https://laminatedplastics.com/polypropylene.pdf, diakses 25 November 2025.

Aryanti, F.I., Pembuatan Komposit Polimer Polipropilena Talk Masterbatch Hitam pada Cover Tail. (2021). Jurnal Teknologi dan Manajemen, 19(01), 1-6. DOI:10.52330/jtm.v19i1.8

Cahyono, T.S.A., Hadi, S., Pratama, R.W. & Amalia, Z. (2024). Fatigue Test of Plastics and Manufacturing Collet Nut Driver for Integrated Rotating Bending Fatigue Test Machine. Logic Jurnal Rancang Bangun dan Teknologi, 24(3):110-116.

Damayanti, K.I., Ramdhani, D., Ramadhan, F. & Setiawan, G.E. (2025). Variation of Plyethylene and Polypropylene on the Quality of Plastic Types. Analit: Analytical and Environmental Chemistry, 9(02), 45-55. DOI: https://doi.org/10.23960/analit.v9i02.186

Dzulfikar, M. & Attho’illah, M. (2021). Pengaruh Variasi Tekanan Compression Moulding terhadap Kekuatan Plastik Daur Ulang dari Bahan Polypropylene. Momentum, 17(1) , Hal. 58-62. DOI:10.36499/mim.v17i1.4349

Hadi, S., Alviano, D.K., Andhika, D.A. & I. Rosdinata, (2025). Pengaruh Penambahan ABS Bekas dan Jenis Plastik ABS Hasil Cetak Injeksi terhadap Umur Lelah. Konstruksi: Publikasi Ilmu Teknik, Perencanaan Tata Ruang dan Teknik Sipil, 4(3), in Press.

Hadi, S., Hardjito, A., Wicaksono, H., Cahyono, T.S.A., Wirawan & Emzain, Z.F. (2023). Fatigue Life Prediction of Injection Molded Polymer. Proceeding of the 5th Annual Advance Technology, Applied Science, and Engineering Confecrence (ATASEC) 2023, 235-248

Hakim, J., Joharwan, J.W. & Palmiyanto, M.H. (2020). Pengaruh Beda Temperatur Proses Injeksi terhadap Sifat Mekanis Bahan Polypropylene (PP) Daur Ulang. Jurnal Material dan Proses Manufaktur, 4(2), 124-135. DOI: https//doi.org/10.18196/jmpm.v4i2.10758

Jones, H., McClements, J., Ray, D., Hindle, C.S., Kalloudis, M. & Koutsos, V. (2023). Thermomechanical Properties of Virgin and Recycled Polypropylene-High-Density Polyethylene Blends. Polymers, 15(4200), 1-20. https://doi.org/10.3390/polym15214200

Khavilla, V.P., Wahyuni, S., Riyanto, A.F., Jumaeri & Harjono, (2019). Preparasi dan Karakterisasi PP (Polypropylene) Termodifikasi LLDPE (Linear Low Density Polyethylene) dengan Teknik Pencampuran Biasa. Indonesian Journal of Chemical Science, 8 (3) , 176-184. http://journal.unnes.ac.id/sju/index.php/ijcs

Latief, A.E., Anggraeni, N.D. & Putera, I. (2022). Perancangan Cetakan Injection Molding Hand Press Material Komposit PPHI dan Serat Alam. Machine: Jurnal Teknik Mesin, 8(2), 12-16. DOI:10.33019/jm.v8i2.2554

Lilin, A. & Siswantoro, T. (2016). Pemanfaatan Material Plastik dan Mold Bekas untuk Perancangan Produk Baru di PT. YPTI. Prosiding Seminar Nasional Multi Disiplin Ilmu ke-2 Tahun 2016, UNISBANK Semarang. 230-243. https://media.neliti.com/media/publications/172198-ID-none.pdf

Mardiyati, Srahputri, N., Steven & Suratman, R. (2017). Sifat Tarik dan Sifat Impak Komposit Polipropilena High Impact Berpenguat Serat Rami Acak yang Dibuat dengan Metode Injection Molding. MESIN, 26(1), 8-16. DOI: https://doi.org/10.5614/MESIN.2017.26.1.2

Marisma, S.A.R., Salim, A.S., Rubianto, L. & Wibawa, A.S.M. (2021). Studi Literatur Karakteristik Produk Pengolahan Daur Ulang Plastik. Distilat, Jurnal Teknologi Separasi, 7 (1), 6-12. DOI: https://doi.org/10.33795/distilat.v7i1.180

Mirza, A., Jaiswal, S. & Modak, J. (2020). Modification and Characterization of Polypropylene Blending with High Impact Polystyrene by Using Compatibilizers. International Research Journal of Engineering and Technology, 07(04), 2699-2701. www.irjet.net

Putra, B.J.A. & Widi, I.K.A. (2025). Analisa Pengaruh Komposisi Plastik PP dengan Abu Sekam pada Mesin Injeksi Molding Semi Otomatis terhadap Uji Impact dan Struktur Makro. Jurnal Mesin Material Manufaktur dan Energi, 5(2) 1-11. DOI: https://doi.org/10.47549/jmmme.v5i2.15792

Rahmawati, A. (2017). Perbandingan Penggunaan Polypropilene (PP) dan High Density Polyethylene (HDPE) pada Campuran Laston WC. Media Teknik Sipil, 15(1), 11-19. DOI:10.22219/jmts.v15i1.4414

Safrudin, A.L., Junaidi, A. & Yunus, M. (2021). Studi Fisis dan Mekanis serta Penyusutan Plastic Polypropylene Dipadukan dengan Plastic Polyethylene. Machinery Jurnal Teknologi Terapan, 2(1), 58-65. DOI: https://doi.org/10.5281/zenodo.4748704

Salisu, A. & Maigari, Y.S. (2021). Polystyrene and its Recycling- a Review. Proceedings of Materials Science and Technology Society of Nigeria (MSN) Kaduna State Chapter, MSNKAD ID 2141, 195-203. https://www.researchgate.net/publication/359135360

Singh, A., Chauhan, A. & Gaur, R. (2025). A Comprehensive Review on the Synthesis, Properties, Environmental Impacts, and Chemiluminescence Applications of Polystyrene (PS). Discover Chemistry, 2(47), 1-31. https://doi.org/10.1007/s44371-025-00125-y

Sugiyanto, D., Chan, Y. & Taoupik, A. (2023). Pengaruh Temperatur dan Tekanan terhadap Hasil Cetakan Polypropylene Menggunakan Mesin Injection Molding Vertikal. Jurnal Konversi Energi dan Manufaktur, 8(2), 131-141. DOI:10.21009/JKEM.8.2.7

Supriono, A.D., Wicaksono, D. & Sehono, (2022). Analisa Kekuatan Polypropylene dengan Campuran Serat Karbon dan HDPE Menggunakan Uji Impact. Teknika STTKD: Jurnal Teknik, Elektronik, Engine, 8(2), 251-256. https://doi.org/10.56521/teknika.v8i2.640