Produksi Obeng Minus-Plus Panjang 160 mm dengan Pegangan Kunci Sok Busi M16, Kapasitas 5 Biji/Jam

Azka Najahaan Arsadani; Syamsul Hadi; Muhammad Rafif Daffa Adz Dzakiru; Muhammad Yusuf Kurniawan; Nabil Iwandaka

doi:10.61132/manufaktur.v4i2.1414

Authors

Azka Najahaan Arsadani Politeknik Negeri Malang
Syamsul Hadi Politeknik Negeri Malang
Muhammad Rafif Daffa Adz Dzakiru Politeknik Negeri Malang
Muhammad Yusuf Kurniawan Politeknik Negeri Malang
Nabil Iwandaka Politeknik Negeri Malang

DOI:

https://doi.org/10.61132/manufaktur.v4i2.1414

Keywords:

160mm Long Screwdriver, Hex Socket Wrench Formation, M16 Spark Plug Socket Wrench, Minus-Plus Screwdriver, Zinc Plated

Abstract

A pair of minus-plus screwdrivers with motorcycle spark plug socket wrench handles that are often lost/lost is a problem. The production objective is to obtain a pair of minus-plus screwdrivers with a length of 160 mm and an M16 spark plug socket wrench. The production objective is to obtain a pair of minus-plus screwdrivers with a length of 160 mm and an M16 spark plug socket wrench. The production method includes: design of a pair of minus-plus screwdrivers and spark plug socket wrenches; selection of minus-plus screwdriver materials with a diameter of 8 mm and a pipe with a diameter of 16 mm x 90 mm, a thickness of 2 mm for socket wrenches from AISI 1045; forming of plus-minus screwdriver bits; forging socket wrenches into hexagons from 16 mm diameter pipes; drilling through the end of 9 mm diameter pipes; making 20 mm long screwdriver shaft torque retainer; installation of torque retainer tightness on the end of 12 mm inner diameter pipes, finishing of screwdriver shafts and socket wrenches; hot-dip galvanization on screwdriver shafts and socket wrenches; quality inspection, dimensions, and open-close packaging. The production results are a pair of 160 mm long minus-plus screwdrivers, 8 mm diameter screwdriver shaft with M16 spark plug socket wrench, 2 mm thickness of AISI 1045 zinc-coated steel, total manufacturing cost of IDR 22,000/unit, manufacturing duration of 12 minutes/unit which has the impact that a pair of minus-plus screwdrivers and socket wrench can be used and can be stored back in the container.

References

Agarwal, A., Kumar, P., Kumar, A. & Ghadai, R. K. (2024). Strategic Design Optimization of Cutting Tools for Enhanced Manufacturing Efficiency. Industry 4.0 Driven Manufacturing Technologies, 251-276. https://doi.org/10.1007/978-3-031-68271-1_11

Akbar, N., Andrijono, D. & Mardjuki (2021). Variasi media pendinginan terhadap kekerasan material logam hasil tempa panas pandai besi. Journal of TRANSMISI Universitas Merdeka Malang, 13(1), 145-156. DOI:https://doi.org/10.26905/jtmt.v13i1.2004

Budayawati, I., Betan, A. D., Abdullah, A., Hore, D., Niron, F. P. & Lantang, L. (2026). Respon Material Akibat Kekerasan Pahat Bubut Hardfacing terhadap Nilai Kekasaran Permukaan. Jurnal Fisika: Fisika Sains dan Aplikasinya, 11(1), 1-8. https://doi.org/10.35508/fisa.v11i1.27605

But, A., Canarache, R. & Gal, L. (2021). Improve Productivity Through Digital Manufacturing. Journal of Production Engineering, 24(2), 35-37. https://doi.org/10.24867/JPE-2021-02-035

Firdaus, R. A., DU, H. D. & Pamungkas, G. P. (2024). Penerapan metode algoritma simpleks pada optimalisasi produksi busi. Jurnal Minfo Polgan, 13(1), 230-240. 10.33395/jmp.v13i1.13598

Feng, C., Guo, H., Zhang, J., Huang, Y. & Huang, S. (2022). A Systematic Method of Optimization of Machining Parameters Considering Energy Consumption, Machining Time, and Surface Roughness with Experimental Analysis. The International Journal of Advanced Manufacturing Technology, 119(11), 7383-7401. https://doi.org/10.21203/rs.3.rs-669643/v1

Gómez-Rocha, J. E., Hernández-Gress, E. S. & Rivera-Gómez, H. (2021). Production Planning of a Furniture Manufacturing Company with Random Demand and Production Capacity Using Stochastic Programming. Plos One, 16(6), 1-26. DOI:10.1371/journal.pone.0252801

Hidayat, W. (2019). Klasifikasi dan Sifat Material Teknik serta Pengujian Material. Jurnal Material Teknik, 4, 1-19. DOI:10.31227/osf.io/6bmfu

Izhardas, J. M. & Lubis, M. S. Y. (2023). Pemanfaatan 3D Printing untuk Pembuatan Pemegang Tools di Workshop Go Kart. Jurnal Serina Sains, Teknik dan Kedokteran, 1(1), 27-34. https://doi.org/10.24912/jsstk.v1i1.22748

Khairina, O. & Jonuarti, R. (2026). Pengaruh Pelapisan Kaolin pada Titanium Dioksida (TiO2) dan Zinc Oksida (ZnO) terhadap Aktivitas Fotokatalitik Lapisan Tipis. Journal of Science, Technology, and Innovation, 1(3), 190-200. https://doi.org/10.65310/zmkk4495

Mario, F. & Setiawan, H. (2019). Perancangan Alat Prush (Pembersih Busi Sederhana) dengan Pendekatan Ergonomi dan Value Engineering (Studi Kasus di UKM Bengkel Motor Koli Palembang). Jurnal Rekayasa Industri (JRI), 1(1), 1-12. https://doi.org/10.37631/jri.v1i1.56

Mughits, H. S., Witjaksono, H. D. P., Suasono, H. S., Atmaja, I. A. S. & Setiawan, R. (2023). Literature Review: Penerapan Metode Single Minutes Exchange of Die (SMED) di Berbagai Sektor Industri Manufaktur. Jurnal Kalibrasi: Karya Lintas Ilmu Bidang Rekayasa Arsitektur, Sipil, Industri, 6(2), 59-69. https://doi.org/10.37721/kalibrasi.v6i2.1124

Pratama, M. A., Rizqi, A. W. & Hidayat, H. (2022). Analisis Resiko K3 pada Pekerjaan Fabrikasi Konstruksi di Cv. Arfa Putra Karya dengan Metode JSA (Job Safety Analysis). Jurnal Teknik Industri: Jurnal Hasil Penelitian dan Karya Ilmiah dalam Bidang Teknik Industri, 8(2), 314-323. http://dx.doi.org/10.24014/jti.v8i2.19569

Raoufi, K., Sutherland, J. W., Zhao, F., Clarens, A. F., Rickli, J. L., Fan, Z. & Haapala, K. R. (2024). Current State and Emerging Trends in Advanced Manufacturing: Process Technologies. The International Journal of Advanced Manufacturing Technology, 135(9), 4089-4118. https://doi.org/10.1007/s00170-024-14782-3

Riansyah, A. F. & Andesta, D. (2026). Analisis Potensi Bahaya Kerja dengan Metode JSA dan HIRARC di Workshop Fabrikasi. Jurnal Teknologi dan Manajemen Industri Terapan, 5(1), 154-162. https://doi.org/10.55826/jtmit.v5i1.1476

Soori, M. & Asmael, M. (2022). A Review of the Recent Development in Machining Parameter Optimization. Jordan Journal of Mechanical and Industrial Engineering, 16(2), 205-223. https://hal.science/hal-03588524v1

Soori, M. & Arezoo, B. (2022). Cutting Tool Wear Prediction in Machining Operations, a Review. Journal of New Technology and Materials, 12(2), 15-26.

Yuniarto, Y., Umardani, Y., Nugroho, A. & Ridwan, M. (2026). Identifikasi dan Kajian Teknologi Spinning untuk Produk Ukir Tembaga. Jurnal Pengabdian Vokasi, 3(4), 403-408, https://doi.org/10.14710/jpv.2024.30669

Zhuang, H., Zhu, F., Na, L., Zhao, C. & Zhang, J. (2024). An Analysis of Modern Machinery Manufacturing Technology and Precision Processing Technology. Mechanical Engineering and Manufacturing Technology, 1(1), 10-14. https://www.hillpublisher.com/Journals/memt/

Wijaya, R. N. (2022). Karakteristik Perambatan Retak Fatik pada Baja Paduan AISI 4140. Skripsi, Jurusan Teknik Mesin Fakultas Teknik Universitas Lampung, 1-59. http://digilib.unila.ac.id/id/eprint/67767